AEG L76285FL Uživatelský manuál

L 76285 FL EN User manual

Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water5.11

ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctionsExtra Silencio-so95° - ColdWhite and colouredcotton with normalsoil.max. 8

ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctions20 Min. - 3 kg40° - 30°Cotton and synthet-ic items with lightsoil or worn o

Programme1)Type of load Max. loadSteam can be used for dried, washed or worn once laundry. These pro-grammes can reduce creases and odours and make yo

Programmes Load(Kg)Energyconsump-tion (kWh)Water con-sumption(litre)Approxi-mate pro-grammeduration(minutes)Remain-ing mois-ture (%)1)Synthetics 40°C4

Make sure not to put too much laun-dry in the drum.3.Close the door.Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwa

Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge

5.Press button 4 to start the pro-gramme. The indicator of button 4is on.The drain pump can operate fora short time when the appliancefills water.The

• The door lock symbol goes off.•Press button 1 to deactivate the ap-pliance. After five minutes from theend of the programme, the energysaving functi

• Do not mix different types of deter-gents.• To help the environment, do not usemore than the correct quantity of de-tergent.• Obey the instructions

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

• Set the hottest cotton wash pro-gramme• Use a correct quantity of powder de-tergent with biological properties.After each wash, keep the door open f

5.Clean the dispenser recess with abrush.6.Put back the dispenser in the recess.11.7 Drain pumpRegularly examine the drainpump and make sure that it i

125.When the container is full of water,put the drainage duct back againand empty the container. Do steps 4and 5 again and again until no morewater fl

To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif

12. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta

Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T

Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai

2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from

127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f

WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

14. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a

ENGLISH 33

34www.aeg.com

ENGLISH 35

www.aeg.com/shop132916910-A-102013

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se

Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 8 kgSpin speed Maximum 1200 rpm1

4.2 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra

D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th