AEG L61470BI Uživatelský manuál

L 61271 BIL 61470 BIEN User manual

ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsCottons + Prewash3)95° - ColdMax. load 7 kg - Reduced load

ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsSpinMax. load 7 kgSeparate spin for hand washed cotton gar

ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptions Cottons Eco5)60° and 40°Max. load 7 kgWhite and fast colo

Programmes Load(Kg)Energyconsump-tion (kWh)Water con-sumption(litre)Approxi-mate pro-grammeduration(minutes)Remain-ing mois-ture (%)1)Delicates 40°C3

Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.9.2 Filling the detergent and a

If you turn the programme dial toanother programme when theappliance is working, the yellowpilot light of button 8 blinks 3times. The display shows th

SUPERQUICKThe relative pilot light re-mains lit.The washing duration willbe reduced to wash lightlysoiled laundry or itemsused or worn for a shorttime

If, for any reason, it is necessary to openit, firstly press the button 8 to set themachine to pauseIf the light B after a few minutes goesoff, the do

• A very small load can cause balanceproblems with the spin phase. If thisoccurs, adjust manually the items inthe tub and start the spin phase again.1

find on the packaging of the manufactur-er.Do this separately from the laundrywash.11.2 External cleaningClean the appliance only with soap andwarm wa

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

5.Clean the dispenser recess with abrush.6.Put back the dispenser in the recess.11.6 Drain pumpThe pump should be inspected regularlyand particularly

6.Remove foreign bodies and flufffrom the filter seat and from thepump impeller.7.Check carefully whether the pumpimpeller rotates (it rotates jerkily

To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif

By doing this, any water remaining in themachine is removed, avoiding ice form-ing and consequently damage to the ap-pliance.When you use the machine

Problem Possible cause/SolutionThe machine does notfill:The water tap is closed. • Open the water tap.The inlet hose is squashed or kinked. • Check th

Problem Possible cause/SolutionUnsatisfactory washingresults:Too little detergent or unsuitable detergent hasbeen used.• Increase the detergent quanti

Problem Possible cause/SolutionNo water is visible inthe drum:Machines based on modern technology operatevery economically using very little water wit

5.Open the door. Remove the poly-styrene piece from the door sealand all the items from the drum.6.Put one of the polystyrene packag-ing elements on t

10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Put the plastic caps in the holes.You can find th

• After having levelled the appliance,tighten the lock nuts.• The appliance must be level and sta-ble.Never place cardboard, wood orsimilar materials

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

• Directly to a built-in drain pipe in theroom wall and tighten it with a clip.You can extend the drain hose tomaximum 400 cm. Contact theservice cent

14. BUILDING IN14.1 Building in600 mm555 mm596 mm170 mm75 mm100 mm60 mmmin.820 mmmin.560 mm818 mm• This appliance has been designed tobe built into th

12• HingesTo mount the hinges it is necessary todrill two holes (dia. 35 mm, depth12.5-14 mm depending on the depthof door furniture) on the inner sid

ABCEDIf the door has to be opened from left toright, invert the position of the plates E ,the magnet D and the plate C. Mountthe counter-magnet D and

www.aeg.com/shop132927083-A-142014

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

mains plug, use a 13 amp ASTA (BS1362) fuse.•This appliance complies with theE.E.C. Directives.Water connection• Make sure not to cause damage to thew

Level of protection against ingress of solid parti-cles and moisture ensured by the protective cover,except where the low voltage equipment has noprot

4.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

5.1 DisplayThe display shows the following informa-tion:Duration of the set programmeWhen you set a programme, the display shows the duration inhours

5.2 Indicator pilot lightsABCAfter you have pressed the button 8, theWASHING light (A) comes on.The machine is operating.The DOOR light (B) indicates