AEG HD955100NB Uživatelský manuál

EN User ManualHobHD955100

lets the thermocouple warm up. Ifnot, the gas supply is interrupted.3. Adjust the flame after it is regular.If after some tries the burnerdoes not lig

• you do not deactivate a cooking zoneor change the heat setting. Aftersome time comes on and the hobdeactivates.The relation between the heat setti

CountUp Timer (The count up timer)You can use this function to monitor howlong the cooking zone operates.To set the cooking zone: touch again and agai

When the function is set to you canhear the sounds only when:• you touch • Minute Minder comes down• Count Down Timer comes down• you put something

CAUTION!Make sure that the bottomsof pots do not stand abovethe control knob, otherwisethe flame heats the controlknob up.CAUTION!Make sure that pot h

Heat setting Use to: Time(min)Hints3 - 5 Simmer rice and milkbaseddishes, heating up ready-cooked meals.25 - 50 Add the minimum twice asmuch liquid as

the dirt can cause damage to the hob.Put the special scraper on the glasssurface at an acute angle and movethe blade on the surface.• Remove when the

Problem Possible cause RemedyAn acoustic signal soundsand the hob deactivates.An acoustic signal soundswhen the hob is deactivated.You put something o

Problem Possible cause Remedy and a number come on.There is an error in the hob. Disconnect the hob from theelectrical supply for sometime. Disconnect

conditions of guarantee are in theguarantee booklet.7.3 Labels supplied with theaccessories bagStick the adhesive labels as indicatedbelow:MOD.PROD.NO

CONTENTS1. SAFETY INFORMATION...32. SAFETY INSTRUCTIONS.

Standards Codes Of Practice: B.S. 6172/B.S. 5440, Par. 2 and B.S. 6891 CurrentEditions.The hob should not be installed in a bedsitting room with a vol

CAUTION!Make sure that the gassupply pressure of theappliance obeys therecommended values.Rigid connection:Carry out connection by using metal rigidpi

of clamps fixed to the side of thecabinet, in order to avoid any contactwith the equipment beneath thecooktop.Electrical RequirementsPermanent electri

phase. There must be no cut or straystrands of wire present. The cordclamp must be correctly attached tothe outer sheath.8.9 Attaching the seal1. Clea

R 5 mmmin.55 mm490 mm830 mm600 mmmin.38 mmmin.2 mmmin.12 mmmin. 2 mmCAUTION!Install the appliance only ona worktop with a flat surface.8.11 Possibilit

safety reasons and to let easy removeoven from the unit.If you install the hobasymmetrically rightward theminimum distance betweenleft edge of the hob

Electric supply: 230 V ~ 50 HzAppliance category: II2H3+ Gas connection: R 1/2" Appliance class: 3 9.5 Gas burners for NATURAL GAS G20 20 mbar

Energy consumption per cookingzone (ECelectric cooking)Centre rear 178.1 Wh / kgRight rear 169.2 Wh / kgCentre front 167.2 Wh / kgRight front 178.1 Wh

www.aeg.com/shop867315831-A-472014

1. SAFETY INFORMATIONBefore the installation and use of the appliance,carefully read the supplied instructions. Themanufacturer is not responsible i

• Do not store items on the cooking surfaces.• Metallic objects such as knives, forks, spoons and lidsshould not be placed on the hob surface since th

• Obey the installation instructionsupplied with the appliance.• Keep the minimum distance from theother appliances and units.• Always be careful when

• This appliance is not connected to adevice, which evacuates the productsof combustion. Make sure to connectthe appliance according to currentinstall

• Do not let acid liquids, for examplevinegar, lemon juice or limescaleremover, touch the hob. This cancause matt patches.2.5 Care and cleaning• Clean

3.3 Control panel layout1 2 35648 7109Use the sensor fields to operate the appliance. The displays, indicators and sounds tellwhich functions operate.

Display DescriptionPower function operates. + digitThere is a malfunction. / / OptiHeat Control (3 step Residual heat indicator): continue cooking /