AEG FFB41600ZM Uživatelský manuál

USER MANUALEN User ManualDishwasherFFB41600ZWFFB41600ZM

Water hardnessGerman de-grees (°dH)French degrees(°fH)mmol/l Clarke de-greesWater softener lev-el47 - 50 84 - 90 8.4 - 9.0 58 - 63 1043 - 46 76 - 83 7

– = rinse aid emptynotification activated.– = rinse aid emptynotification deactivated.2. Press Start to change the setting.3. Press on/off to confir

Activating options can affectthe water and energyconsumption as well as theprogramme duration.7.1 XtraDry （增强烘干）Activate this option to boost the dryi

4. Carefully shake the funnel by itshandle to get the last granulesinside.5. Remove the salt around the openingof the salt container.6. Turn the cap o

2. Press the on/off button to activatethe appliance.Make sure that the appliance is inprogramme selection mode.• If the salt indicator is on, fill the

Opening the door while theappliance operatesOpening the door while a programme isrunning stops the appliance. It may affectthe energy consumption and

• In areas with hard and very hard waterwe recommend to use plaindishwasher detergent (powder, gel,tablets containing no additionalagents), rinse aid

11. CARE AND CLEANINGWARNING!Before maintenance,deactivate the appliance anddisconnect the mains plugfrom the main socket.Dirty filters and cloggedspr

CAUTION!An incorrect position of thefilters can cause badwashing results and damageto the appliance.11.2 Cleaning the spray armsDo not remove the spra

Problem and alarm code Possible cause and solutionThe program does not start. • Make sure that the appliance door is closed.• Press Start （启动）.• If th

CONTENTS1. SAFETY INFORMATION...22. SAFETY INSTRUCTIONS...

Problem and alarm code Possible cause and solutionThe appliance trips the cir-cuit-beaker.• The amperage is insufficient to supply simultaneously allt

Problem Possible cause and solutionThe dishes are wet. • For the best drying performance activate the optionXtraDry （增强烘干） and set AirDry （空气对流干燥） .•

Refer to "Before first use", "Daily use" or "Hints andtips" for other possiblecauses.13. PRODUCT INFORMATION SHEETTrade

Water supply pressure Min. / max.bar (MPa)0.5 (0.05) / 8 (0.8)Water supplyCold water or hot water 2)max 60 °C1) Refer to the rating plate for other va

ENHazardous substancesParts Name Pb Hg Cd Cr6+ PBBs PBDEsCabinetXTubSump & hydraulics (including pumps, heater & sensors)XSoftener & inner

ENGLISH 25

www.aeg.com26

ENGLISH 27

www.aeg.com/shop156928961-A-372018

may occur. Before the installation and use of theappliance, carefully read the supplied instructions. Themanufacturer is not responsible for any injur

• The operating water pressure (minimum andmaximum) must be between 0.5 (0.05) / 8 (0.8) bar(MPa)• Obey the maximum number of 13 place settings.• If t

• Connect the mains plug to the mainssocket only at the end of theinstallation. Make sure that there isaccess to the mains plug after theinstallation.

3. PRODUCT DESCRIPTION54810 9 116712 2311Worktop2Upper spray arm3Lower spray arm4Filters5Rating plate6Salt container7Air vent8Rinse aid dispenser9Dete

4. CONTROL PANEL12 4 568371On/off button2Program button3Programme indicators4Display5Delay button6Option button7Indicators8Start button4.1 IndicatorsI

Indicator DescriptionExtraHygiene indicator.Door indicator. It comes on when the appliance door is open or is not cor-rectly closed.5. PROGRAMMESThe o

Programme 1)Water(l)Energy(kWh)Duration(min)14 - 15 1.5 - 1.7 155 - 17010 0.8 301) The pressure and the temperature of the water, the variations of th