AEG L60270FL Uživatelský manuál

L 60270 FL EN User manual

6. PROGRAMMESProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsCottons95° - ColdWhite and colouredcotton with normalsoil.max

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsDrainAll fabricsThe maximum loadof the laundry is rela-ted to the type ofl

programmes in terms of combined energy and water consumption for washing normallysoiled cotton laundry.Set this programme to have a good washing resul

Off Mode (W) Left On Mode (W)The information given in the charts above are in compliance with the EU Com-mission regulation 1015/2010 implementing dir

9.2 Filling the detergent and additivesThe detergent compartment for the prewash phase, the soakprogramme and for the stain function.Add the detergent

3.To use powder detergent, turn theflap up.4.To use liquid detergent, turn theflap down.With the flap in the positionDOWN:– Do not use gelatinous or t

2.Turn again the programme knob toa new washing programme. At thistime you can also set the availablefunctions.The appliance does not drain thewater.9

2.Press the Start/Pause button 4 .The appliance drain the water andspin.3.When the programme is completedand the door lock symbol goes off,you can ope

• mmol/l (millimol for each litre - inter-national unit for the hardness of wa-ter).• Clarke degrees.Water hardness tableLevel TypeWater hardness°dH °

11.5 DrumRegularly examine the drum to preventlimescale and rust particles.Only use special products to remove rustparticles from the drum.To do this:

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

WARNING!1.Disconnect the mains plugfrom the mains socket.2.Do not remove the filterwhile the appliance oper-ates. Do not clean the drainpump if the wa

7.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.218.Clean the filter under the water tapand put

4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur

• - The appliance does not drainthe water.• - The appliance door is open ornot closed correctly.WARNING!Deactivate the appliance beforeyou do the chec

Problem Possible cause Possible solution Balance problems withthe laundry load.Adjust manually the items in thetub and start the spin phaseagain.The

Problem Possible cause Possible solutionThe washing re-sults are not satis-factory.The detergent you usedwas not sufficient or cor-rect.Increase the d

4.Remove the internal film.5.Open the door and remove all theitems from the drum.6.Put one of the polystyrene packag-ing elements on the floor behindt

9.Remove the power supply cable andthe drain hose from the hose hold-ers.10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out

13.3 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

14. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a

www.aeg.com/shop132930712-A-212013

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se

Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 7 kgSpin speed Maximum 1200 rpm1

4.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra

5.6 Time save button 6Press the button 6 to decrease theprogramme duration.• Press one time to set 'Shortened dura-tion' for items with dail